Overview

Farrow & Ball Wood Primer & Undercoat is a water-based base coat for interior and exterior wood designed to be used under Estate Eggshell, Modern Eggshell, Exterior Eggshell, Full Gloss or Dead Flat. This protective base can be used on bare and previously painted wood such as floorboards and knots. Available in four shades to match your chosen topcoat colour and crafted with high-quality ingredients, each one has been carefully formulated to add richness and depth and deliver that signature Farrow & Ball look with a long-lasting finish once your topcoat is applied. Using Farrow & Ball Wood Primer & Undercoat will also ensure your topcoat adheres effortlessly to the surface you are painting while providing a durable, even finish.

• Apply before using Estate Eggshell, Modern Eggshell, Exterior Eggshell, Full Gloss or Dead Flat
• Prepares the surface for topcoat
• Quick drying
• Low odour & Low VOC

Tinted Colour Information

Preparation

Ensure all surfaces are sound, clean, dry and free from dirt, grease and other contamination.

Knotty or Resinous Wood Preparation:

• Heat the knot to draw out any excess resin (we recommend using a hot air paint stripper).
• Scrape off any residue resin, and then thoroughly clean the area with white or methylated spirit. Allow the area to dry thoroughly before continuing.

New and Unpainted Interior Wood (Not Floors) Preparation:

• Fill any cracks, holes and open joints with an appropriate filler.
• To improve the paint's adhesion, lightly sand the surface.
• Prepare any filled, knotty or resinous areas as above and patch prime with
• Apply one coat of in the correct colour tone for your top coat. Allow a minimum of 4 hours drying time between coats.
• Apply two coats of your chosen Farrow & Ball finish, allowing the correct drying time between coats.

Previously Painted Interior Wood (Not Floors) Preparation:

• Remove any areas of old paint which are peeling or blistering as flaking or peeling can occur if you paint over weak paint layers. Blend and 'feather' the edges of areas of old paint, as this helps to smooth out the surface.
• Fill any cracks, holes and open joints with an appropriate filler.
• Lightly sand the surface to improve paint adhesion.
• Patch prime any filled or bare knotty / resinous areas with .
• Apply one coat of , in the correct colour tone for your top coat (and allowing a minimum of 4 hours drying time between coats).
• Then apply two coats of your chosen Farrow & Ball finish, allowing the correct drying time between coats.

Exterior Bare Wood Surface Preparation:

• Fill any cracks, holes and open joints with an appropriate filler.
• To improve the paint's adhesion, lightly sand the surface.
• In environments where wood rotting fungi is likely to occur, treat with exterior wood preservative prior to priming.
• Prepare any knotty or resinous areas as above and patch prime with .
• Apply one coat of , in the correct colour tone for your top coat, and allow a minimum of 4 hours drying time.
• Apply two coats of your chosen Farrow & Ball finish, allowing the correct drying time between coats.

Please note: Not suitable for exterior decking or other pressure treated wood.

Exterior Previously Painted Wood Surface Preparation:

• Remove any areas of old paint which are peeling or blistering as flaking or peeling can occur if you paint over weak paint layers. Blend and 'feather' the edges of areas of old paint, as this helps to smooth out the surface.
• Fill any cracks, holes and open joints with a water-based exterior wood filler.
• Lightly sand the surface to improve paint adhesion.
• In environments where wood rotting fungi is likely to occur, treat with exterior wood preservative prior to priming.
• Prepare any knotty or resinous areas as above and patch prime with .
• Apply one coat of , in the correct colour tone for your top coat (and allowing a minimum of 4 hours drying time between coats).
• Then apply two coats of your chosen Farrow & Ball finish, allowing the correct drying time between coats.

Please note: Repeatedly repairing cracks, holes and open joints in a surface may indicate that the surface is nearing the end of its life and will require additional effort to maintain it. If this is the case consider renewal or replacement.

Find out more information about the preparation of various surfaces on the "Product Advice Sheet" in the "Datasheet" section.

Application

Always test a small area of the surface to be painted to ensure compatibility

Don't over dilute the Primer & Undercoat or mist coat. This will reduce their opacity, causing an uneven finish and incomplete colour development. Before applying the top coat, consider if a second, undiluted coat of Primer & Undercoat is needed to achieve full opacity.

• Stir thoroughly before use.
• Ensure all surfaces are sound, clean, dry and free from dirt, grease and other contamination. Please note that flaking or peeling may occur if you paint over weak paint layers - to avoid this sand back any previous weak paint layers before you start painting.
• For most applications, a quality fine-tipped synthetic bristled paint brush or medium pile woven polyester roller is recommended.

Find out more information about the Application on the "Product Advice Sheet" in the "Datasheet" section.

Always follow manufacturer's instructions found on the tin

For the very best results, Farrow & Ball always recommend using a Farrow & Ball Primer & Undercoat.

Recommended Primer & Undercoats:

• For use on wood:
• For use on metal:
• For use on interior walls & ceilings:
• For use to patch prime unsound masonry surfaces : Farrow & Ball Masonry & Plaster Stabilising Primer

Aftercare & Storage

Protect from frost and extreme temperatures.

It is recommended to use this product within 6 months of purchase therefore, we are unable to accept responsibility for the deterioration of contents or packaging after this date.

Find out more information on the "Product Advice Sheet" in the "Datasheet" section.